Light-Initiated Imprinted Membrane-Based Biomimetic SERS Sensor toward Selective Detection of Trace MC-LR.

Microcystin-LR (MC-LR) is a severe threat to human and animal health; thus, monitoring it in the environment is essential, especially in water quality protections. Herein, in this work, we synthesize PVDF/CNT/Ag molecular imprinted membranes (PCA-MIMs) via an innovative combination of surface-enhanced Raman spectroscopy (SERS) detection, membrane separation, and molecular-imprinted technique toward the analysis of MC-LR in water. In particular, a light-initiated imprint is employed to protect the chemical structure of the MC-LR molecules. Furthermore, in order to ensure the detection sensitivity, the SERS substrates are combined with the membrane via the assistance of magnetism. The effect of synthesis conditions on the SERS sensitivity was investigated in detail. It is demonstrated from the characteristic results that the PCA-MIMs present high sensitivity to the MC-LR molecules with excellent selectivity against the interfere molecules. Results clearly show that the as-prepared PCA-MIMs hold great potential applications to detect trace MC-LR for the protection of water quality.

Short-term outcomes of a multicentre prospective study using a "visible" polyvinylidene fluoride onlay mesh for the prevention of midline incisional hernia.

INTRODUCTION: Prophylactic meshes in high-risk patients prevent incisional hernias, although there are still some concerns about the best layer to place them in, the type of fixation, the mesh material, the significance of the level of contamination, and surgical complications. We aimed to provide answers to these questions and information about how the implanted material behaves based on its visibility under magnetic resonance imaging (MRI). METHOD: This is a prospective multicentre observational cohort study. Preliminary results from the first 3 months are presented. We included general surgical patients who had at least two risk factors for developing an incisional hernia. Multivariate logistic regression was used. A polyvinylidene fluoride (PVDF) mesh loaded with iron particles was used in an onlay position. MRIs were performed 6 weeks after treatment. RESULTS: Between July 2016 and June 2022, 185 patients were enrolled in the study. Surgery was emergent in 30.3% of cases, contaminated in 10.7% and dirty in 11.8%. A total of 5.6% of cases had postoperative wound infections, with the requirement of stoma being the only significant risk factor (OR = 7.59, p = 0.03). The formation of a seroma at 6 weeks detected by MRI, was associated with body mass index (OR = 1.13, p = 0.02). CONCLUSIONS: The prophylactic use of onlay PVDF mesh in midline laparotomies in high-risk patients was safe and effective in the short term, regardless of the type of surgery or the level of contamination. MRI allowed us to detect asymptomatic seromas during the early process of integration. STUDY REGISTRATION:  This protocol was registered at ClinicalTrials.gov (NCT03105895).

Flexible 3D Force Sensor Based on Polymer Nanocomposite for Soft Robotics and Medical Applications.

The three-dimensional (3D) force sensor has become essential in industrial and medical applications. The existing conventional 3D force sensors quantify the three-direction force components at a point of interest or extended contact area. However, they are typically made of rigid, complex structures and expensive materials, making them hard to implement in different soft or fixable industrial and medical applications. In this work, a new flexible 3D force sensor based on polymer nanocomposite (PNC) sensing elements was proposed and tested for its sensitivity to forces in the 3D space. Multi-walled carbon nanotube/polyvinylidene fluoride (MWCNT/PVDF) sensing element films were fabricated using the spray coating technique. The MWCNTs play an essential role in strain sensitivity in the sensing elements. They have been utilized for internal strain measurements of the fixable 3D force sensor's structure in response to 3D forces. The MWCNT/PVDF was selected for its high sensitivity and capability to measure high and low-frequency forces. Four sensing elements were distributed into a cross-beam structure configuration, the most typically used solid 3D force sensor. Then, the sensing elements were inserted between two silicone rubber layers to enhance the sensor's flexibility. The developed sensor was tested under different static and dynamic loading scenarios and exhibited excellent sensitivity and ability to distinguish between tension and compression force directions. The proposed sensor can be implemented in vast applications, including soft robotics and prostheses' internal forces of patients with limb amputations.

Stability, homogeneity and measurement uncertainty estimation of PVP-I solutions for the application on oro and nasopharynx against SARS-CoV-2.

Aqueous solution containing different concentration (0.5, 0.6 and 1.0%) (w/v) of Polyvinyl pyrrolodon-Iodine (PVP-I) complex, a well-known antiseptic; is prepared and the stability and homogeneity of these solution is assessed as per the ICH Guidelines and International Harmonized Protocol respectively. The solutions were found to be sufficiently homogeneous and stable for a year at 25 °C (60%RH). Measurement uncertainty of the prepared PVP-I solutions were estimated by identifying possible sources of uncertainty using Ishikawa diagram and preparing uncertainty budget based on scope of calibration laboratory. The stable and homogenized PVP-I solution is to be used in a clinical trial for the application on oro and nasopharynx against novel SARS-CoV-2 Virus.

Insights into Factors Affecting Ethylene-Vinyl Acetate Copolymer Crystallinity in Islatravir Implant.

Islatravir, a highly potent nucleoside reverse transcriptase translocation inhibitor (NRTTI) for the treatment of HIV, has great potential to be formulated as ethylene-vinyl acetate (EVA) copolymer-based implants via hot melt extrusion. The crystallinity of EVA determines its physical and rheological properties and may impact the drug-eluting implant performance. Herein, we describe the systematic analysis of factors affecting the EVA crystallinity in islatravir implants. Differential scanning calorimetry (DSC) on EVA and solid-state NMR revealed drug loading promoted EVA crystallization, whereas BaSO4 loading had negligible impact on EVA crystallinity. The sterilization through γ-irradiation appeared to significantly impact the EVA crystallinity and surface characteristics of the implants. Furthermore, DSC analysis of thin implant slices prepared with an ultramicrotome indicated that the surface layer of the implant was more crystalline than the core. These findings provide critical insights into factors affecting the crystallinity, mechanical properties, and physicochemical properties of the EVA polymer matrix of extruded islatravir implants.

Photoinduced charge generation of nanostructured carbon derived from human hair biowaste for performance enhancement in polyvinylidene fluoride based triboelectric nanogenerator.

Carbon nanostructures derived from human hair biowaste are incorporated into polyvinylidene fluoride (PVDF) polymer to enhance the energy conversion performance of a triboelectric nanogenerator (TENG). The PVDF filled with activated carbon nanomaterial from human hair (AC-HH) exhibits improved surface charge density and photoinduced charge generation. These remarkable properties are attributed to the presence of graphene-like nanostructures in AC-HH, contributing to the augmented performance of PVDF@AC-HH TENG. The correlation of surface morphologies, surface charge potential, charge capacitance properties, and TENG electrical output of the PVDF composites at various AC-HH loading is studied and discussed. Applications of the PVDF@AC-HH TENG as a power source for micro/nanoelectronics and a movement sensor for detecting finger gestures are also demonstrated. The photoresponse property of the fabricated TENG is demonstrated and analyzed in-depth. The analysis indicates that the photoinduced charge carriers originate from the conductive reduced graphene oxide (rGO), contributing to the enhanced surface charge density of the PVDF composite film. This research introduces a novel approach to enhancing TENG performance through the utilization of carbon nanostructures derived from human biowaste. The findings of this work are crucial for the development of innovative energy-harvesting technology with multifunctionality, including power generation, motion detection, and photoresponse capabilities.

Fabrication and In-Vivo Evaluation of Polyvinyl pyrrolidone/Poloxamer 188 Hybrid Nanofibers of Deflazacort.

The superior flexibility, efficient drug loading, high surface-to-volume ratio, ease of formulation, and cost-controlled production are considered exceptional advantages of nanofibers (NFs) as a smart delivery system. Deflazacort (DEF) is an anti-inflammatory and immunosuppressant agent. It is categorized as a poorly soluble class II drug. In this study, DEF-loaded polymeric nanofibrous using the electrospinning technique mats, Polyvinyl pyrrolidone (PVP) with or without Poloxamer 188 (PX) were used as mat-forming polymers. Microscopical imaging, drug content (%), and in vitro dissolution studies were conducted for all NFs formulae (F1-F7). All NFs improved the DEF dissolution compared to the unprocessed form, with the superiority of the PVP/PX hybrid. The optimized formula (F7) exhibited an average diameter of 655.46 ± 90.4 nm and % drug content of 84.33 ± 5.58. The dissolution parameters of DEF loaded in PVP/PX NFs (F7) reflected a release of 95.3 % ± 3.1 and 102.6 % ± 1.7 after 5 and 60 min, respectively. NFs (F7) was investigated for drug-polymer compatibility using Fourier-Transform Infrared Spectroscopy (FTIR), Powder X-ray diffraction analysis (PXRD), and Differential Scanning Calorimetry (DSC). In vivo anti-inflammatory study employing male Sprague-Dawley rats showed a significant reduction of rat paw edema for F7 (p < 0.05) compared with unprocessed DEF with a normal epidermal and dermal skin structure comparable to the healthy negative control. Immunohistochemical and morphometric data displayed similarities between the immune reaction of F7 and the negative healthy control. The finding of this work emphasized that DEF loaded in PVP/PX NFs could be considered a useful strategy for enhancing the therapeutic performance of DEF.

Postpolymerization Modification of Poly(2-vinyl-4,4-dimethyl azlactone) as a Versatile Strategy for Drug Conjugation and Stimuli-Responsive Release.

Postpolymerization modification of highly defined "scaffold" polymers is a promising approach for overcoming the existing limitations of controlled radical polymerization such as batch-to-batch inconsistencies, accessibility to different monomers, and compatibility with harsh synthesis conditions. Using multiple physicochemical characterization techniques, we demonstrate that poly(2-vinyl-4,4-dimethyl azlactone) (PVDMA) scaffolds can be efficiently modified with a coumarin derivative, doxorubicin, and camptothecin small molecule drugs. Subsequently, we show that coumarin-modified PVDMA has a high cellular biocompatibility and that coumarin derivatives are liberated from the polymer in the intracellular environment for cytosolic accumulation. In addition, we report the pharmacokinetics, biodistribution, and antitumor efficacy of a PVDMA-based polymer for the first time, demonstrating unique accumulation patterns based on the administration route (i.e., intravenous vs oral), efficient tumor uptake, and tumor growth inhibition in 4T1 orthotopic triple negative breast cancer (TNBC) xenografts. This work establishes the utility of PVDMA as a versatile chemical platform for producing polymer-drug conjugates with a tunable, stimuli-responsive delivery.

Dislocation force of scleral flange-fixated intraocular lens haptics.

PURPOSE: To measure the dislocation forces in relation to haptic material, flange size and needle used. SETTING: Hanusch Hospital, Vienna, Austria. DESIGN: Laboratory Investigation. METHODS, MAIN OUTCOME MEASURES: 30 G (gauge) thin wall and 27 G standard needles were used for a 2 mm tangential scleral tunnel in combination with different PVDF (polyvinylidene fluoride) and PMMA (polymethylmethacrylate haptics). Flanges were created by heating 1 mm of the haptic end, non-forceps assisted in PVDF and forceps assisted in PMMA haptics. The dislocation force was measured in non-preserved cadaver sclera using a tensiometer device. RESULTS: PVDF flanges achieved were of a mushroom-like shape and PMMA flanges were of a conic shape. For 30 G needle tunnels the dislocation forces for PVDF and PMMA haptic flanges were 1.58 ± 0.68 N (n = 10) and 0.70 ± 0.14 N (n = 9) (p = 0.003) respectively. For 27 G needle tunnels the dislocation forces for PVDF and PMMA haptic flanges were 0.31 ± 0.35 N (n = 3) and 0.0 N (n = 4), respectively. The flange size correlated with the occurring dislocation force in experiments with 30 G needle tunnels (r = 0.92), when flanges were bigger than 384 micrometres. CONCLUSIONS: The highest dislocation forces were found for PVDF haptic flanges and their characteristic mushroom-like shape for 30 G thin wall needle scleral tunnels. Forceps assisted flange creation in PMMA haptics did not compensate the disadvantage of PMMA haptics with their characteristic conic shape flange.

Modifying gas transfer membranes with nanoscale zero-valent iron: effects on membrane material properties, treatment performance, and biofilm thickness.

Excessive membrane biofilm growth on membrane fibers depends on various factors, with membrane properties playing a pivotal role in influencing microbial affinity for the membrane. To investigate the antibacterial impact of nano-sized zero-valent iron (nZVI) on membrane biofilm structure, pristine (polyvinylidene fluoride (PVDF)) only: HF-0 (PVDF:20/nZVI:0 w/w) and four gas transfer membranes (PVDF:nZVI at different concentrations: HF-1 (PVDF:20/nZVI:0.25 w/w), HF-2 (PVDF:20/nZVI:0.50 w/w), HF-3 (PVDF:20/nZVI:0.75 w/w), HF-4 (PVDF:20/nZVI:1.0 w/w)) were produced. These membranes were assessed for surface morphology, porosity, gas permeability, and biofilm thickness, which ultimately affect biochemical reaction rates in membrane biofilm reactors (MBfRs). Various MBfRs utilizing these gas transfer membranes were operated at different hydraulic retention times (HRTs) and oxygen pressures to assess chemical oxygen demand (COD) removal efficiency and nitrification performance. Incorporating nZVI into the PVDF polymer solution increased surface hydrophilicity and porosity but reduced Young's Modulus and oxygen diffusion coefficients. Confocal laser scanning microscopy (CLSM) analysis revealed an average biofilm thickness of 700 µm in HF-0, HF-1, and HF-3, with a 100 µm decrease in HF-2, even though Escherichia coli growth was observed in HF-3 fibers. Regardless of nZVI dosage, a significant decline in COD removal and nitrification rates occurred at low HRTs and gas pressures.

Easily scale 3D conductive gradient fiber membrane for contaminants removal and fouling mitigation under electrochemical assistance.

An electrochemical membrane filtration system provides an innovative approach to enhance contaminant removal and mitigate membrane fouling. There is an urgent need to develop portable, versatile, and efficient electrochemical membranes for affordable wastewater treatment. Here, a 3D conductive gradient fiber membrane (CC/PVDF) with a gradient porous structure was prepared using a two-step phase inversion method. Methyl orange (MO) was utilized as model organic substance to investigate the electrochemical performance of the CC/PVDF membrane. At applied potentials of +2 V, +3 V, -2 V and -3 V, the removal efficiency of MO was 5.1, 5.3, 4.8, and 5.1 times higher than at 0 V. A dramatic flux loss of 35.02% occurred on the membrane without electrochemistry, interestingly, whereas the flux losses were only 23.59%-10.24% in the applied potential after 30 min of filtration, which were approximately 1.18, 1.28, 1.29 and 1.38 times as high as that without electrochemistry, respectively. The enhanced removal and anti-fouling performances of the membranes were attributed to the functions of electrochemical degradation, electrostatic repulsion, and electrically enhanced wettability. Electrochemical generation of Hydrogen peroxide, along with HO• radicals, was detected and direct electron transfer and HO• were proved to be the dominant oxidants responsible for MO degradation. The intermediate oxidation products were identified by mass spectrometry, and an electrochemical degradation pathway of MO was proposed based on bond-breaking oxidation, ring-opening reactions, and complete oxidation. All the findings emphasize that the ECMF system possesses superior efficiency and creative potential for water purification applications.

Formulation and characterization of glipizide solid dosage form with enhanced solubility.

Glipizide, a poor water-soluble drug belongs to BCS class II. The proposed work aimed to enhance the solubility of glipizide by preparing solid dispersions, using polyvinyl pyrrolidone (PVP) and polyethylene glycol (PEG). Solvent evaporation method was used for the preparation of glipizide solid dispersions. Solid dispersions were prepared in four different drug-to-polymer ratios i.e. 1:1, 1:2, 1:3 and 1:4. Mainly effect of three polymers (PVP K30, PVP K90 and PEG 6000) was evaluated on the solubility and dissolution of glipizide. The in-vitro dissolution of all prepared formulations was performed under pH 6.8 at 37°C using USP type II apparatus. In-vitro dissolution results revealed that the formulations having high concentrations of the polymer showed enhanced solubility. Enhancements in the solubility and rate of dissolution of the drug were noted in solid dispersion formulations compared to the physical blends and pure drug. Solid dispersions containing polyvinyl pyrrolidone exhibited a more favorable pattern of drug release compared to the corresponding solid dispersions with PEG. An increase in the maximum solubility of the drug within the solid dispersion systems was observed in all instances. Two solid dispersion formulations were optimized and formulated into immediate-release tablets, which passed all the pharmacopoeial and non-pharmacopoeial tests. Fourier transformed Infrared (FTIR) spectroscopy X-ray diffraction (XRD) and Differential scanning calorimetry (DSC) were used to indicate drug: polymer interactions in solid state. Analysis of the solid dispersion samples through characterization tests indicated the compatibility between the drug and the polymer.

In vitro neuronal and glial response to magnetically stimulated piezoelectric poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV)/cobalt ferrite (CFO) microspheres.

Polymer biomaterials are being considered for tissue regeneration due to the possibility of resembling different extracellular matrix characteristics. However, most current scaffolds cannot respond to physical-chemical modifications of the cell microenvironment. Stimuli-responsive materials, such as electroactive smart polymers, are increasingly gaining attention once they can produce electrical potentials without external power supplies. The presence of piezoelectricity in human tissues like cartilage and bone highlights the importance of electrical stimulation in physiological conditions. Although poly(vinylidene fluoride) (PVDF) is one of the piezoelectric polymers with the highest piezoelectric response, it is not biodegradable. Poly(hydroxybutyrate-co-hydroxyvalerate) (PHBV) is a promising copolymer of poly(hydroxybutyrate) (PHB) for tissue engineering and regeneration applications. It offers biodegradability, piezoelectric properties, biocompatibility, and bioactivity, making it a superior option to PVDF for biomedical purposes requiring biodegradability. Magnetoelectric polymer composites can be made by combining magnetostrictive particles and piezoelectric polymers to further tune their properties for tissue regeneration. These composites convert magnetic stimuli into electrical stimuli, generating local electrical potentials for various applications. Cobalt ferrites (CFO) and piezoelectric polymers have been combined and processed into different morphologies, maintaining biocompatibility for tissue engineering. The present work studied how PHBV/CFO microspheres affected neural and glial response in spinal cord cultures. It is expected that the electrical signals generated by these microspheres due to their magnetoelectric nature could aid in tissue regeneration and repair. PHBV/CFO microspheres were not cytotoxic and were able to impact neurite outgrowth and promote neuronal differentiation. Furthermore, PHBV/CFO microspheres led to microglia activation and induced the release of several bioactive molecules. Importantly, magnetically stimulated microspheres ameliorated cell viability after an in vitro ROS-induced lesion of spinal cord cultures, which suggests a beneficial effect on tissue regeneration and repair.

Sodium alginate/ager colourimetric film on porous substrate layer: Potential in intelligent food packaging.

Colourimetric indicators have potential applications in monitoring food freshness and offer a simple, rapid, effective, and economical approach. Blending sodium alginate (SA) with agar (AG), an ideal choice for solid substrates in colourimetric indicators, can modify mechanical compliance and optical properties. However, the limitations in the water-sustaining capacity and dye migration of hydrogel substrates significantly impede the scalability and commercial application of these indicators. In this study, we designed and prepared a bilayer-structured indicator featuring an SA/AG colourimetric film on a porous Polypropylene fluoride (PVDF)/SiO2 encapsulation film. This design aims to enhance the water-sustaining capacity and reduce dye migration from the SA/AG colourimetric film. The PVDF/SiO2 composite film was prepared using a peeling-assisted phase-conversion process, which enabled the indicator to selectively allow gas, but not water, to pass through its porous substrate. Furthermore, we tested the layered indicator film by monitoring changes in shrimp freshness. The results revealed significant and distinguishable colour changes in the indicators corresponding to the freshness and spoilage of the shrimp.

Development of a duplex droplet digital PCR assay for the detection of Burkholderia cepacia complex and Stenotrophomonas maltophilia in bloodstream infections.

Burkholderia cepacia complex (BCC) and Stenotrophomonas maltophilia are nosocomial pathogens that cause various infections and exhibit high resistance to multiple antimicrobial agents. In this study, we aimed to develop a duplex droplet digital PCR (ddPCR) assay for detecting BCC and S. maltophilia in bloodstream infections. We optimized the experimental conditions by setting the annealing temperature to 51°C and determining the optimal concentrations of primers and probes, as well as the thermal cycle numbers. The feasibility of the duplex ddPCR reaction system with the optimal conditions was established and verified through parallel reactions with reference strains of BCC and S. maltophilia. The specificity of the assay, tested with 33 reference strains, was found to be 100%. The duplex ddPCR assay demonstrated good repeatability and could detect as low as 5.35 copies/reaction of BCC and 7.67 copies/reaction of S. maltophilia. This level of sensitivity was consistent in the simulated blood and blood bottle samples. We compared nucleic acid extraction methods and found that the Chelex-100 boiling method and kit extraction method exhibited similar detection sensitivity, suggesting the potential application of the Chelex-100 boiling method in the ddPCR assay. In the clinical samples, the duplex ddPCR assay accurately detected BCC and S. maltophilia in 58 cases. In conclusion, our study successfully developed a duplex ddPCR assay that provides accurate and convenient detection of BCC and S. maltophilia in bloodstream infections.IMPORTANCEBurkholderia cepacia complex (BCC) and Stenotrophomonas maltophilia are implicated in a wide range of infections, including bloodstream infections (BSIs), pneumonia, and meningitis, and often exhibit high intrinsic resistance to multiple antimicrobial agents, limiting therapeutic options. The gold standard for diagnosing bloodstream infections remains blood culture. However, current blood culture detection and positivity rates do not meet the "rapid diagnosis" required for the diagnosis and treatment of critically ill patients with BSIs. The digital droplet PCR (ddPCR) method is a potentially more powerful tool in the diagnosis of BSIs compared to other molecular methods due to its greater sensitivity, specificity, accuracy, and reproducibility. In this study, a duplex ddPCR assay for the detection of BCC and S. maltophilia in BSIs was developed.

Selective Detection of NH3 Gas by Ti3C2Tx Sensors with the PVDF-ZIF-67 Overlayer at Room Temperature.

In the realm of NH3 gas-sensing applications, the electrically conductive nature of Ti3C2Tx MXene, adorned with surface terminations such as -O and -OH groups, renders it a compelling material. However, the inherent challenges of atmospheric instability and selectivity in the presence of gas mixtures have prompted the exploration of innovative solutions. This work introduces a strategic solution through the deposition of a mixed-matrix membrane (MMM) composed of poly(vinylidene fluoride) (PVDF) as the matrix and zeolitic imidazolate framework-67 (ZIF-67) as the filler. This composite membrane acts as a selective filter, permitting the passage of a specific gas, namely NH3. Leveraging the hydrophobic and chemically inert nature of PVDF, the MMM enhances the atmospheric stability of Ti3C2Tx by impeding water molecules from interacting with the MXene. Furthermore, ZIF-67 is selective to NH3 gas via acid-base interactions within the zeolite group and selective pore size. The Ti3C2Tx sensor embedded in the MMM filter exhibits a modest 1.3% change in the sensing response to 25 ppm of NH3 gas compared to the response without the filter. This result underscores the filter's effectiveness in conferring selectivity and diffusivity, particularly at 35% relative humidity (RH) and 25 °C. Crucially, the hydrophobic attributes of PVDF impart heightened stability to the Ti3C2Tx sensor even amidst varying RH conditions. These results not only demonstrate effective NH3 detection but also highlight the sensor's adaptability to diverse environmental conditions, offering promising prospects for practical applications.

Electroactive poly(vinylidene fluoride-trifluoroethylene)/graphene composites for cardiac tissue engineering applications.

Electroactive materials are increasingly being used in strategies to regenerate cardiac tissue. These materials, particularly those with electrical conductivity, are used to actively recreate the electromechanical nature of the cardiac tissue. In the present work, we describe a novel combination of poly(vinylidene fluoride-trifluoroethylene) (P(VDF-TrFE)), a highly electroactive polymer, with graphene (G), exhibiting high electrical conductivity. G/P(VDF-TrFE) films have been characterized in terms of topographical, physico-chemical, mechanical, electrical, and thermal properties, and studied the response of cardiomyocytes adhering to them. The results indicate that the crystallinity and the wettability of the composites remain almost unaffected after G incorporation. In turn, surface roughness, Young modulus, and electric properties are higher in G/P(VDF-TrFE). Finally, the composites are highly biocompatible and able to support cardiomyocyte adhesion and proliferation, particularly surface treated ones, demonstrating the suitability of these materials for cardiac tissue engineering applications.

Succinylation-Alcian Blue Staining of Mucins on Polyvinylidene Difluoride Membrane.

Mucins are often stained with the basic dye Alcian blue, but mucins with a low acidic glycan content cannot be stained with it. Succinylation-Alcian blue staining is a method that temporarily modifies glycans with succinic acid to visualize mucins with low acidic glycan content. This method can be used to stain mucins on polyvinylidene difluoride (PVDF) membranes separated via supported molecular matrix electrophoresis (SMME) and mucins blotted onto PVDF membranes from gel electrophoreses. The succinyl groups of the modified glycans can be easily and completely removed by releasing O-glycan from the stained mucin bands. Therefore, the glycans can be analyzed using the same methods as those used for mucins with a high acidic glycan content.

Wearable Magnetoelectric Stimulation for Chronic Wound Healing by Electrospun CoFe2O4@CTAB/PVDF Dressings.

Magnetoelectric stimulation is a promising therapy for various disorders due to its high efficacy and safety. To explore its potential in chronic skin wound treatment, we developed a magnetoelectric dressing, CFO@CTAB/PVDF (CCP), by electrospinning cetyltrimethylammonium bromide-modified CoFe2O4 (CFO) particles with polyvinylidene fluoride. Cetyltrimethylammonium bromide (CTAB) serves as a dispersion surfactant for CFO, with its quaternary ammonium cations imparting antibacterial and hydrophilic properties to the dressing. Electrospinning polarizes polyvinylidene fluoride (PVDF) molecules and forms a fibrous membrane with flexibility and breathability. With a wearable electromagnetic induction device, a dynamic magnetic field is established to induce magnetostrictive deformation of CFO nanoparticles. Consequently, a piezoelectric potential is generated on the surface of PVDF nanofibers to enhance the endogenous electrical field in the wound, achieving a cascade coupling of electric-magnetic-mechanical-electric effects. Bacteria and cell cultures show that 2% CTAB effectively balances antibacterial property and fibroblast activity. Under dynamic magnetoelectric stimulation, the CCP dressing demonstrates significant upregulation of TGF-ß, FGF, and VEGF, promoting L929 cell adhesion and proliferation. Moreover, it facilitates the healing of diabetic rat skin wounds infected with Staphylococcus aureus within 2 weeks. Histological and molecular biology evaluations confirm the anti-inflammatory effect of CTAB and the accelerated formation of collagen and vessel by electrical stimulation. This work provides insights into the application of magnetoelectric stimulation in the healing of chronic wounds.

Effect of chitosan crosslinking time on the structure and antifouling performance of polyvinylidene fluoride membrane by surface gelation-immersion precipitation phase inversion.

Polyvinylidene fluoride (PVDF) porous membrane was prepared by a two-step method of surface gelation-immersion precipitation phase inversion. Chitosan/acetic acid solution and glutaraldehyde aqueous solution were sequentially sprayed onto the surface of the PVDF solution film, with chitosan crosslinking and gelation occurring simultaneously on the film surface. The solution film was then immersed in a coagulation bath to obtain a modified PVDF porous membrane. The effect of the crosslinking time of chitosan and glutaraldehyde on the structure and properties of the PVDF porous membrane was discussed. The results showed that with the prolongation of crosslinking time, the surface structure of the membrane changed from a dense skin layer to a porous structure; the porosity and the mean pore size of the modified PVDF membranes increased first and then decreased, and the contact angle gradually decreased. When the crosslinking time extended to 15 min, the water flux of modified membrane (M153) reached a maximum value. BSA dynamic cyclic filtration experiment showed that the retention rate (R) of the modified membrane was significantly improved, compared to 68.3% retention rate of the blank membrane (M000), but the crosslinking time had little effect on the retention rates of the four modified membranes. The antifouling data showed that the flux recovery rate of the blank membrane was 73.0%, while the flux recovery rate of the modified membrane can reach as high as 84.40%, and the irreversible pollution rate of the blank membrane was 27.7%, while the irreversible pollution rate of the modified membrane reduced to 15.6%. These results indicated that, after surface chitosan crosslinking, the hydrophilicity and antifouling properties of PVDF membranes were improved. PRACTITIONER POINTS: Modified PVDF membranes with crosslinking CS coating were prepared by a two-step method of surface gelation-immersion precipitation phase inversion. -OH groups and -NH2 groups of CS coating improve the hydrophilicity and the antifouling property of modified PVDF membranes. Modified PVDF membranes had larger mean pore size and higher porosity than unmodified membrane. Flux recovery rates of the modified membranes were higher than that of unmodified membrane. Pollution degree, reversible pollution rate, and irreversible pollution rate of modified membranes were lower than those of unmodified membrane.